View PA51_4353497.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

P r o d u c t II n n o v a t ii o n F r o m Product nnovat on From
PA51 PA51A PA51 **PA51A
FEATURES
* WIDESUPPLYRANGE--10to40V * HIGHOUTPUTCURRENT--10APeak * CLASS"C"OUTPUT--LowCost * LOWQUIESCENTCURRENT--2.6mA
APPLICATIONS
* DCSERVOAMPLIFIER * MOTOR/SYNCHRODRIVER * VALVEANDACTUATORCONTROL * DCORACPOWERREGULATOR
8-PINTO-3 PACKAGESTYLECE TYPICALAPPLICATION
DESCRIPTION
The PA51 and PA51A are high voltage, high output current operational amplifiers designed to drive resistive, inductive and capacitive loads. Their complementary common emitter output stage is the simple class C type optimized for low frequency applications where crossover distortion is not critical. These amplifiers are not recommended for audio, transducer or deflection coil drive circuits. The safe operating area (SOA) is fully specified and can be observed for all operating conditions by selection of user programmable current limiting resistors. Both amplifiers are internally compensated for all gain settings. For continuous operation under load, mounting on a heatsink of proper rating is recommended. Do not use isolation washers! This hybrid integrated circuit utilizes thick film conductors, ceramic capacitors and semiconductor chips to maximize reliability, minimize size and give top performance. Ultrasonically bonded aluminum wires provide reliable interconnections at all operating temperatures. The 8-pin TO-3 package is electrically isolated and hermetically sealed. The use of compressible thermal washers and/or improper mounting torque will void the product warranty. Please see "General Operating Considerations".
The linear relationship of torque output to current input of the modern torque motor makes this simple control circuit ideal for many material processing and testing applications. The sense resistor develops a feedback voltage proportional to motor current and the small signal properties of the Power Op Amp insure accuracy. With this closed loop operation, temperature induced impedance variations of the motor winding are automatically compensated.
EXTERNALCONNECTIONS
EQUIVALENTSCHEMATIC
Cirrus Logic, Inc. PA51U http://www.cirrus.com
Copyright (c) Cirrus Logic, Inc. 2007 (All Rights Reserved)
NOV 2007 1 PA51U rev Q
PA51 * PA51A
ABSOLUTE MAXIMUM RATINGS SPECIFICATIONS
Product Innovation From
ABSOLUTEMAXIMUMRATINGS
SUPPLY VOLTAGE, +VS to -VS OUTPUT CURRENT, within SOA POWER DISSIPATION, internal INPUT VOLTAGE, differential INPUT VOLTAGE, common mode TEMPERATURE, junction1 TEMPERATURE, pin solder -10s TEMPERATURE RANGE, storage OPERATING TEMPERATURE RANGE, case PA51 TYP 5 10 35 20 15 .05 .02 12 .05 250 10 3 VS-3 110 115 1 16 45 VS-5 VS-4 2 2.6
80V 10A 97W 37V VS 200C 300C -65 to +150C -55 to +125C PA51A TYP 2 * * * * * * 5 * * * * * * * * * * * * * *
SPECIFICATIONS
PARAMETER INPUT OFFSET VOLTAGE, initial OFFSET VOLTAGE, vs. temperature OFFSET VOLTAGE, vs. supply OFFSET VOLTAGE, vs. power BIAS CURRENT, initial BIAS CURRENT, vs. temperature BIAS CURRENT, vs. supply OFFSET CURRENT, initial OFFSET CURRENT, vs. temperature INPUT IMPEDANCE, common mode INPUT IMPEDANCE, differential INPUT CAPACITANCE COMMON MODE VOLTAGE RANGE3 COMMON MODE REJECTION, DC3 GAIN OPEN LOOP GAIN at 10Hz GAIN BANDWIDTH PRODUCT @ 1MHz POWER BANDWIDTH PHASE MARGIN OUTPUT VOLTAGE SWING3 VOLTAGE SWING3 VOLTAGE SWING3 CURRENT SETTLING TIME to .1% SLEW RATE CAPACITIVE LOAD, unity gain CAPACITIVE LOAD, gain > 4 POWER SUPPLY VOLTAGE CURRENT, quiescent THERMAL RESISTANCE, AC, junction to case4 RESISTANCE, DC, junction to case RESISTANCE, junction to air TEMPERATURE RANGE, case TEST CONDITIONS 2, 5 TC = 25C Full temperature range TC = 25C TC = 25C TC = 25C Full temperature range TC = 25C TC = 25C Full temperature range TC = 25C TC = 25C TC = 25C Full temperature range TC = 25C, VCM = VS -6V Full temp. range, full load TC = 25C, full load TC = 25C, IO = 8A, VO = 40VPP Full temperature range TC = 25C, IO = 10A Full temp. range, IO = 4A Full temp. range, IO = 68mA TC = 25C TC = 25C, 2V step TC = 25C, RL = 6 Full temperature range Full temperature range Full temperature range TC = 25C F > 60Hz F < 60Hz Meets full range specifications -25 MIN
MAX 10 65 40 30
MIN
MAX 8 40 30 10
UNITS mV V/C V/V V/W nA nA/C nA/V nA nA/C M M pF V dB dB MHz kHz V V V A s V/s nF
VS-6 70 94 10
* 80 * *
VS-8 VS-6 VS-6 10 1.0
* * * * 1.5 SOA 36 10 1.2 1.8 +85 -55 *
* * 40 * * * +125
10
28 2.6 1.0 1.5 30
*
34 * * * *
V mA C/W C/W C/W C
NOTES: * The specification of PA51A is identical to the specification for PA51 in applicable column to the left. 1. Long term operation at the maximum junction temperature will result in reduced product life. Derate internal power dissipation to achieve high MTTF. 2. The power supply voltage specified under the TYP rating applies unless otherwise noted as a test condition. 3. +VS and -VS denote the positive and negative supply rail respectively. Total VS is measured from +VS to -VS. 4. Rating applies if the output current alternates between both output transistors at a rate faster than 60Hz. 5. Full temperature range specifications are guaranteed but not 100% tested.
CAUTION
The internal substrate contains beryllia (BeO). Do not break the seal. If accidentally broken, do not crush, machine, or subject to temperatures in excess of 850C to avoid generating toxic fumes.
2

PA51U
Product Innovation From
PA51 * PA51A
TYPICAL PERFORMANCE GRAPHS
PA51U

3
PA51 * PA51A
OPERATING CONSIDERATIONS
Product Innovation From
GENERAL
Please read Application Note 1 "General Operating Considerations" which covers stability, supplies, heat sinking, mounting, current limit, SOA interpretation, and specification interpretation. Visit www.apexmicrotech.com for design tools that help automate tasks such as calculations for stability, internal power dissipation, current limit and heat sink selection. The "Application Notes" and "Technical Seminar" sections contain a wealth of information on specific types of applications. Package outlines, heat sinks, mounting hardware and other accessories are located in the "Packages and Accessories" section. Evaluation Kits are available for most Apex product models, consult the "Evaluation Kit" section for details. For the most current version of all Apex product data sheets, visit www.apexmicrotech.com. 1. Under transient conditions, capacitive and dynamic* inductive loads up to the following maximums are safe: CAPACITIVE LOAD VS 40V 35V 30V 25V 20V 15V ILIM = 5A 400F 800F 1,600F 5.0mF 10mF 20mF ILIM = 10A 200F 400F 800F 2.5mF 5.0mF 10mF INDUCTIVE LOAD ILIM = 5A 11mH 20mH 35mH 50mH 400mH ** ILIM = 10A 4.3mH 5.0mH 6.2mH 15mH 20mH 100mH
SAFEOPERATINGAREA(SOA)
The output stage of most power amplifiers has three distinct limitations: 1. The current handling capability of the transistor geometry and the wire bonds. 2. The second breakdown effect which occurs whenever the simultaneous collector current and collector-emitter voltage exceeds specified limits. 3. The junction temperature of the output transistors.
* If the inductive load is driven near steady state conditions, allowing the output voltage to drop more than 8V below the supply rail with ILIM = 10A or 15V below the supply rail with ILIM = 5A while the amplifier is current limiting, the inductor should be capacitively coupled or the current limit must be lowered to meet SOA criteria. ** Second breakdown effect imposes no limitation but thermal limitations must still be observed. 2. The amplifier can handle any EMF generating or reactive load and short circuits to the supply rail or shorts to common if the current limits are set as follows at TC = 85C. VS 45V 40V 35V 30V 25V 20V 15V SHORT TO VS C, L, OR EMF LOAD 0.1A 0.2A 0.3A 0.5A 1.2A 1.5A 2.0A SHORT TO COMMON 1.3A 1.5A 1.6A 2.0A 2.4A 3.0A 4.0A
These simplified limits may be exceeded with further analysis using the operating conditions for a specific application. 3.The output stage is protected against transient flyback. However, for protection against sustained, high energy flyback, external fast-recovery diodes should be used.
CURRENTLIMIT
Proper operation requires the use of two current limit resistors, connected as shown in the external connection diagram. The minimum value for RCL is .06 ohm, however for optimum reliability it should be set as high as possible. Refer to the "General Operating Considerations" section of the handbook for current limit adjust details.
The SOA curves combine the effect of of all limits for this Power Op Amp. For a given application, the direction and magnitude of the output current should be calculated or measured and checked against the SOA curves. This is simple for resistive loads but more complex for reactive and EMF generating loads. The following guidelines may save extensive analytical efforts.
4

PA51U
Product Innovation From
PA51 * PA51A
Copyright (c) 2007 Cirrus Logic, Inc. All rights reserved Printed in the USA Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained is this document is accurate and reliable. However, the information is subject to change without notice and is provided `as is' without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied upon is current and complete. All products are sold subject to the terms and conditions of sales supplied at the time of order acknowledgement, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and, by furnishing this information, Cirrus grants no license, express or implied, under any patents. Mask work rights, copyrights, trademarks, trade secrets, or other intellectual property rights. No part of this publication may be copied, reproduced, stored in a retrieval system, or transmitted, in any for or by any means (electronic, mechanical, photographic, or otherwise) unless distributed in its entirety with all copyright notices attached. No part of this publication may be used as a basis for manufacture or sale of any items without the prior written consent of Cirrus. Certain applications using semiconductor products may involve potential risks of death, personal injury, or severe property or environmental damage ("critical applications"). Cirrus products are not designed, authorized, or warranted to be suitable for use in products surgically implanted into the body, automotive safety or security devices, life-support products or other critical applications, inclusion of Cirrus products in such applications is understood to be fully at the customer's risk and cirrus disclaims and makes no warranty of merchantability and fitness for particular purpose, with regard to any Cirrus product that is used in such a manner. If the customer uses or permits the use of Cirrus products in critical products in critical applications, customer agrees, by such use, to fully indemnify Cirrus, its officers, directors, employees, distributors and other agents from any and all liability, including attorneys' fees and costs that may result from or arise in connection with these uses. Cirrus Logic, Cirrus, the Cirrus Logic logo designs, Apex, and Apex Precision Power are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners.
CIRRUS LOGIC, INC. * 5980 N SHANNON ROAD, TUCSON, AZ 85741 USA * TELEPHONE (520) 690-8600 APPLICATIONS SUPPORT (800) 546-2739 * FAX (520) 888-3329 * EMAIL support@cirrus.com ORDERS (520) 690-8601 * FAX (520) 690-7749 * EMAIL teamsales@cirrus.com
PA51U

5

▲Up To Search▲

Price & Availability of PA51

	To Download PA51 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .